• myGriffith
    • Staff portal
    • Contact Us⌄
      • Future student enquiries 1800 677 728
      • Current student enquiries 1800 154 055
      • International enquiries +61 7 3735 6425
      • General enquiries 07 3735 7111
      • Online enquiries
      • Staff phonebook
    View Item 
    •   Home
    • Griffith Theses
    • Theses - Higher Degree by Research
    • View Item
    • Home
    • Griffith Theses
    • Theses - Higher Degree by Research
    • View Item
    JavaScript is disabled for your browser. Some features of this site may not work without it.

    Browse

  • All of Griffith Research Online
    • Communities & Collections
    • Authors
    • By Issue Date
    • Titles
  • This Collection
    • Authors
    • By Issue Date
    • Titles
  • Statistics

  • Most Popular Items
  • Statistics by Country
  • Most Popular Authors
  • Support

  • Contact us
  • FAQs
  • Admin login

  • Login
  • Fabrication of Micro-Mirrors in Silicon Optical Waveguides

    Thumbnail
    View/Open
    Powell_2004_01Thesis.pdf (7.870Mb)
    Author(s)
    Powell, Oliver J.
    Primary Supervisor
    Harrison, Barry
    Year published
    2004
    Metadata
    Show full item record
    Abstract
    The conventional large radii bends used in large cross section silicon-on-insulator waveguides were replaced with novel wet etched corner mirrors, potentially allowing much smaller devices, therefore lower costs. If such corners had been based on reactive ion etch techniques they would have had the disadvantage of rougher surfaces and poor alignment in the vertical direction. Wet etching overcomes these two problems by providing smooth corner facets aligned precisely to the vertical {100} silicon crystallographic planes. The waveguides obtained had angled walls, and so numerical analysis was undertaken to establish the single ...
    View more >
    The conventional large radii bends used in large cross section silicon-on-insulator waveguides were replaced with novel wet etched corner mirrors, potentially allowing much smaller devices, therefore lower costs. If such corners had been based on reactive ion etch techniques they would have had the disadvantage of rougher surfaces and poor alignment in the vertical direction. Wet etching overcomes these two problems by providing smooth corner facets aligned precisely to the vertical {100} silicon crystallographic planes. The waveguides obtained had angled walls, and so numerical analysis was undertaken to establish the single mode condition for such trapezoidal structures. To show the relationship between fabrication tolerances and optical losses a three dimensional simulation tool was developed, based on expansion of the incident mode into plane waves. Various new fabrication techniques were are proposed, namely: the use of titanium as a mask for deep silicon wet anisotropic etching, a technique for aligning masks to the crystal plane on silicon-oninsulator wafers, a corner compensation method for sloping sidewalls, and the suppression of residues and pyramids with the use of acetic acid for KOH etching. Also, it was shown that isopropyl alcohol may be used in KOH etching of vertical walls if the concentration and temperature are sufficiently high. As the proposed corner mirrors were convex structures the problem of undercutting by high order crystal planes arose. This was uniquely overcome by the addition of some structures to effectively convert the convex structures into concave ones. The corner mirrors had higher optical losses than were originally hoped for, similar to those of mirrors in thin film waveguides made by RIE. The losses were possibly due to poor angular precision of the lithography process. The design also failed to provide adequate mechanisms to allow the etch to be stopped at the optimal time. The waveguides had the advantage over thin film technology of large, fibre-compatible cross sections. However the mirror losses must be reduced for the technology to compete with existing large cross section waveguides using large bends. Potential applications of the technology are also discussed. The geometry of the crystal planes places fundamental limits on the proximity of any two waveguides. This causes some increase in the length of MMI couplers used for channel splitting. The problem could possibly be overcome by integrating one of the mirrors into the end of the MMI coupler to form an L shaped junction.
    View less >
    Thesis Type
    Thesis (PhD Doctorate)
    Degree Program
    Doctor of Philosophy (PhD)
    School
    School of Microelectronic Engineering
    DOI
    https://doi.org/10.25904/1912/1215
    Copyright Statement
    The author owns the copyright in this thesis, unless stated otherwise.
    Item Access Status
    Public
    Subject
    silicon-on-insulator waveguides
    silicon optical waveguides
    micro-mirrors
    wet etching
    reactive ion etching
    Publication URI
    http://hdl.handle.net/10072/365595
    Collection
    • Theses - Higher Degree by Research

    Footer

    Disclaimer

    • Privacy policy
    • Copyright matters
    • CRICOS Provider - 00233E

    Tagline

    • Gold Coast
    • Logan
    • Brisbane - Queensland, Australia
    First Peoples of Australia
    • Aboriginal
    • Torres Strait Islander